125 Amp Wire Size
What gauge wire do you need for a 125 amp circuit? The short answer, the full NEC 310.16 table at all three termination ratings, and how far you can run it before voltage drop forces a bigger conductor.
Short answer
A 125 amp circuit needs 1 AWG copper, or 2/0 AWG aluminium, sized from the 75°C column of NEC 310.16.
At 240 V that copper conductor stays inside a 3% voltage drop for roughly 192 ft one-way. Past that, go up a size.
A 125 A breaker may serve a continuous load of no more than 100 A (NEC 210.19/215.2, the 125% rule).
Minimum conductor by termination rating
Terminations on breakers, lugs and equipment carry a temperature rating. You size the conductor from the lowest-rated component in the circuit, so the same 125 A load can call for different sizes.
| Termination rating | Copper | Aluminium |
|---|---|---|
| 60°C | 1/0 AWG (125 A) | 3/0 AWG (130 A) |
| 75°C (applies here) | 1 AWG (130 A) | 2/0 AWG (135 A) |
| 90°C | 2 AWG (130 A) | 1/0 AWG (135 A) |
NEC 110.14(C)(1) requires the 60°C column for circuits rated 100 A or less unless every termination is listed for a higher temperature, and the 75°C column above 100 A. Most modern breakers and panels are listed 75°C, which is why the 75°C size is often what actually gets installed. The 90°C column is normally used only as a starting point for derating, not for the final size.
How far can you run it?
Ampacity sets the minimum size; voltage drop sets the maximum distance. These are one-way run lengths at 125 A on a 240 V single-phase circuit, holding drop to 3%.
| Copper size | Max one-way run at 3% | Max one-way run at 5% |
|---|---|---|
| 1 AWG | 192 ft | 321 ft |
| 1/0 AWG | 242 ft | 403 ft |
| 2/0 AWG | 286 ft | 477 ft |
| 3/0 AWG | 373 ft | 622 ft |
3% is the NEC's recommended limit for a branch circuit and 5% for feeder plus branch combined. Both are recommendations in informational notes, not enforceable rules, but most inspectors and specifiers treat 3% as the working target.
What runs on a 125 amp circuit
Typical loads at this rating: larger sub-panels, small commercial services, feeders to accessory dwelling units.
125 A is a standard NEC 240.6 breaker size and a common panel rating, sitting between the 100 A and 150 A feeder tiers.
Check your exact run
These figures assume a standard installation with no derating. For your actual length, voltage, conductor material and temperature, run the numbers:
Ampacities are NEC 310.16 reference values for not more than three current-carrying conductors at 30°C ambient. They do not include ambient-temperature or conductor-bundling derating, and local wiring rules take precedence. Verify against the applicable code before installing.
Frequently Asked Questions
What size wire do I need for a 125 amp breaker?
1 AWG copper, or 2/0 AWG aluminium, sized from the 75°C column of NEC 310.16. Where every termination in the circuit is listed for 75°C, 1 AWG copper is permitted.
Can I use aluminium wire for a 125 amp circuit?
Yes, provided the terminations are rated for aluminium (marked AL or CU-AL) and an antioxidant compound is used. Aluminium has lower ampacity for a given size, so you need 2/0 AWG aluminium in place of 1 AWG copper. It is cheaper and lighter on long feeder runs, which is why services are often aluminium.
How far can I run 1 AWG at 125 amps?
About 192 ft one-way on a 240 V single-phase circuit before voltage drop reaches 3%. Beyond that, step up one conductor size for every further increment of length.
What is the largest continuous load on a 125 amp circuit?
100 A. A continuous load is one expected to run for three hours or more, and NEC 210.19 and 215.2 require the circuit to be rated at 125% of it. That is why, for example, EV chargers are always on a breaker well above their charging current.
Does this include derating?
No. These are base ampacities for not more than three current-carrying conductors at 30°C ambient. If you have more conductors in a raceway, a hot attic, or conduit in direct sun, apply the NEC 310.15 adjustment and correction factors, which will push the required size up.
Related Calculators
Continue with these related electrical tools
Wire Size Calculator
Smallest conductor that meets ampacity and the voltage-drop limit (AWG/mm2)
Voltage Drop Calculator
Voltage drop over a run by length, current and conductor (AWG/mm2, 1ph/3ph/DC)
Breaker / Fuse Sizing Calculator
Next standard breaker or fuse size for a load (NEC 240.6)
Conduit Fill Calculator
NEC conduit fill percentage by conductor size and count
Electrical Calculators
Fast, free calculators for electricians and engineers
Tools
- Voltage Drop Calculator
- Wire Size Calculator
- AWG Conversion Calculator
- Ohm's Law Calculator
- Watts Amps Volts Calculator
- Three-Phase Power Calculator
- kVA Calculator
- LED Resistor Calculator
- Conduit Fill Calculator
- Transformer Sizing Calculator
- Breaker / Fuse Sizing Calculator
- Motor FLA Calculator
- Power Factor Correction Calculator
- Battery Runtime Calculator
- Solar PV Sizing Calculator
- Energy Cost Calculator (kWh)
- Resistor Colour Code Calculator
- Fault Current Calculator
- All Tools
Guides
Resources
More Calculators
- Flow Rate Calculator Pump, pipe and flow rate tools
- Solar Sizing Calculator Solar, battery and off-grid sizing tools
© 2026 Electrical Calculators. All rights reserved.